您好,欢迎来到济南新雄经贸有限公司官方网站!

400-0616-756

行业动态

Industrydynamics

产品中心
当前位置: 首页-新闻中心-行业动态-高强度塑料合金钢管的制作结构与材料

高强度塑料合金钢管的制作结构与材料

来源:http://www.jnxxjm.com

【 发布于:2019-06-10 16:25:46 】


1,外观与构造

1. Appearance and structure

(1)圆内但方形外双层复合构造,挤压成型,能够放置在不同直径的电缆,和原来的水泥堵管,波纹管和其他管能够自在转换,分离,并有相应的配件如衔接器,插头,勒带,特殊的胶,修补和便于施工操作。如图1所示。高强度塑料合金钢管构造(甲:乙:丙:外形的内墙厚度)

(1) Double-layer composite structure inside the circle but outside the square, extrusion forming, can be placed in different diameter cables, and the original cement plug pipe, corrugated pipe and other pipes can be freely converted and separated, and there are corresponding accessories such as connectors, plugs, strangles, special glue, repair and easy construction operation. As shown in Figure 1. Structures of High Strength Plastic Alloy Steel Pipe (A: B: C: Thickness of Internal Wall of Shape)

(2)构造尺寸表1构造尺寸标准的最小直径(毫米)外形(毫米)每根长度(米)壁厚度(毫米)在92毫米规格不低于8392x92(6±0.5)(+0.03)不小于3.5 在110规格不低于100110x110(6±0.5)(+0.03)不少于4.4

(2) Structure Dimension Table 1 Minimum Diameter (Millimeter) Profile (Millimeter) of Standard Construction Dimension (Millimeter) Wall Thickness per Length (Millimeter) at 92mm Specification is not less than 8392x92 (6 + 0.5) (+0.03) at least 3.5 at 110mm Specification is not less than 100110x110 (6 + 0.5) (+0.03) at least 4.4

(3)外形构造为弧角方形,管角度:15±毫米。

(3) The shape is arc-angle square, and the tube angle is 15 + mm.

20171219904795.jpg

(4)内壁润滑,线程模型。

(4) Inner wall lubrication, thread model.

(5)管颜色平均,管外壁,不允许泡沫,裂纹,合成变色线、明显的杂质缺陷。

(5) tube color is average, no foam, crack, synthetic color line and obvious impurity defect are allowed.

(6)管道两端面应平整和垂直于中心轴管轴方向,不应该有明显的弯曲现象。变形不大于20毫米,每米。

(6) Both ends of the pipeline should be flat and perpendicular to the axis of the central axle, and there should be no obvious bending phenomenon. Deformation is not more than 20 mm per meter.

(7)衔接器,插头产品外观无缺陷,损伤性能,尺寸契合设计请求。

(7) Connector, plug product appearance without defect, damage performance, size conforms to design requirements.

2,资料

2. Information

(1)采用优质工程塑料挤出。

(1) Extrusion with high quality engineering plastics.

(2)灵敏性:弯曲,6米管,弯曲强度大于1米。

(2) Sensitivity: Bending, 6m tube, bending strength greater than 1m.

(3)在不同的酸碱度的环境,耐腐蚀,抗老化性能

(3) Corrosion resistance and aging resistance in different acidity and alkalinity environments

(4)(从灭火冒烟即),其熄灭性能应契合有关规则t5169.71985国标/规范。

(4) The extinguishing performance shall conform to the relevant national standard/specification t5169.71985.

(5)50年后的生活。

(5) Life after 50 years.

(6)特殊的胶水可能不包含肿块,不溶性微粒和其它杂质;不胶体状态;不得有分层,无搅拌的条件没有沉淀。

(6) Special glue may not contain lumps, insoluble particles and other impurities; no colloidal state; no stratification; no precipitation without agitation.

3,性能请求

3. Performance Request

性能请求项目条件的性能请求 92mm110mm规格规格 1impact性能0公斤,℃,1.5m9/10through9/10 该2compressive强度千牛/平方米≥300千牛/米400,≥ 3拉伸屈从强度 ≥30 MPa≥30 MPa 4维卡软化温度/ t8802≥82℃≥82℃ 5低温跌落实验- 20℃米高度,不开裂,开裂 6tensile老化后在120℃,6- 20~20% - 20~20% 728~32%盐酸腐蚀电阻小于1.50g/ m2less比1.50g/平方米 28~32%硫酸 38~42氢氧化钠

Performance Request Item Conditions Performance Request 92mm 110mm Specification 1impact Performance 0 kg, C, 1.5m9/10through9/10 This 2compressive strength 1000/m2 (> 300 kb/m 400), > 3 Tensile yield strength (> 30 MPa (> 30 MPa) > 4 Vicat softening temperature (> t8802 (> 82 (> 82 (> 5) Low Temperature Drop Test - 20 (?) m height, no cracking, 6 tensile aging at 120 (?), 6-20-2 (?) The corrosion resistance of 0% - 20% - 20% - 728 - 32% hydrochloric acid is less than 1.50g/m2less than 1.50g/m2 and 28 - 32% sulfuric acid is 38 - 42 sodium hydroxide.

以上就是今天小编为大家介绍关于济南镀锌管的相关的资讯,您可以及时的关注我们的网址:http://www.jnxxjm.com查询了解更多的详情咨询,我们会有更多的精彩内容为您呈现.

Above is the information about Jinan galvanized pipe introduced by today's edition. You can pay attention to our website in time: http://www.jnxxjm.com for more detailed consultation. We will have more wonderful content for you.



上一篇:镀锌风管的安装应该按照哪些操作流程?
下一篇:直缝焊管与螺旋焊管的分类有哪些不同?